How To Install Replace Ignition Switch Ford Ranger 95-04 1AAuto.com

www.1aauto.com 1A Auto shows you how to repair, install, fix, change or replace a damaged, worn out, faulty or shorted ignition switch. This video is applicable to 1995-2004 Ford Ranger models.
Video Rating: 4 / 5

25 Responses to How To Install Replace Ignition Switch Ford Ranger 95-04 1AAuto.com

  • 1aauto says:

    It sounds like there could possibly a frayed wire in the column. If the truck starts when you hit the column, there could be a loose or frayed wire in there.

  • 1aauto says:

    It may be worn out. 

  • MeaghanLovesDestery says:

    I have an 96 madza b2300. i pulled the key out of the ignition an the steering wheel did not lock and the engine did not shut off. would replacing the ignition switch be my solution?

  • 1aauto says:

    There could be a draw or an issue with the radio itself too. You may want to look at it.

  • dannyboyatki says:

    Hi , would replacing this switch maybe help a problem I have where the radio/clock stays on even when the key is removed sometimes.

  • justin d says:

    i need some help i have a 2002 ford ranger and it woint start sometimesi replaced the starter switch bought a new battery and it still woint start it will start 90 percent of the time but when it woint start all you got 2 do is hit the steering coluim and it will start right up i took it to a lock smith and he said it could be a bad antenna he made me a brand new transponder key

  • justin d says:

    i replaced the starter switch bought a new battery and it still woint start it will start 90 percent of the time but when it woint start all you got 2 do is hit the steering coluim and it will start right up i took it to a lock smith and he said it could be a bad antenna he made me a brand new transponder key

  • 1aauto says:

    It sounds like something in the switch may be worn or loose, which could cause the vehicle not to start until you wiggle the part and those pieces make contact again.

  • 1aauto says:

    Yes this is the same switch that is used on the 1998 Ford Explorer. We carry them on our website 1aauto.com 888-844-3393 Part Number: 1AZIS00008

  • BlacknRedTed says:

    Can you guys tell me if this is close to the same set up for a 1998 Ford Explorer XLT model ? If so, I can do this myself and save alot of money.

  • justin d says:

    How do you know if your switch is bad i have a 2002 ford ranger 2.3 4 cyl and it will start fine but ever once and a wile it woint start at all and if you wiggle the switch a little bit it will start i put a brand new battery on. Thanks

  • 1aauto says:

    This video will show you how to replace the switch (not rewire) but replace it. 1aauto.com/1A/IgnitionSwitch/Ford/CrownVictoria/1AZIS00008/486013/1994

  • jestaking says:

    how do you replace the ignition switch connector(re-wire and replace) on a 1994 crown victoria

  • Narc0SkiiLzZ says:

    thanks for your help im going to try this then and ill tell you if it worked

  • 1aauto says:

    You may have to trace the wiring to see if there’s a wire touching a piece of metal somewhere or that could be possibly corroded causing it to short out.

  • Narc0SkiiLzZ says:

    I have a question.
    I have a 1988 Mercury Grand Marquis 5.0L FI 8cyl
    the problem is that i had to disconnect the battery because the starter will start with out me putting the key in and i been having this problem for months and kant find the problem for it and i really need to fix it but don’t know what could be the problem. Can u please help me 1aauto?

  • 1aauto says:

    We do have this one, that shows you how to replace the key lock switch on a 90-96 Ford Ranger. youtube.com/watch?v=PWGrv0hba08&feature=plcp

  • 06mrrayray says:

    Do y’all have a video on how to replace ignition lock

  • krborders says:

    Is it pretty much the same as the ford ranger

  • 1aauto says:

    We currently do not have an auto repair video that shows this on your particular application. Some of the basics may be the same as shown in this video. We do carry a replacement ignition switch for your 1998 Grand Marquis. they are available on our website 1aauto.com Part# 1AZIS00008 or call sales 888-844-3393

  • krborders says:

    how do you replace a ignition switch on a 1998 grand marquis

  • 1aauto says:

    We currently do not have an auto repair video on that particular repair for that vehicle. A Chiltons or a Haynes manual should also show you how to remove it. We sell the Haynes manuals on our website. Here’s a link to them. Hope this helps you out. 1aauto.com/1A/repairmanual/For­d/CrownVictoria/1AMNL00064/219­998/1988?utm_source=youtube&ut­m_medium=youtube&utm_campaign=­1ATony

  • MrDuccimane says:

    wheres the video on how to put an ignition switch on a 1988 ford ltd crown victoria

  • 1aauto says:

    We’ll keep this in mind if we need to make this repair in the future. They usually aren’t to hard to fix. A Haynes or Chiltons manual should show you how to make this repair and where it’s located on your vehicle. We sell the Haynes manuals on our website 1aauto.com

  • dpl1108121 says:

    if you could do a video on where that is located on the ranger! That would help me out big time.. also is it hard to fix that?

Leave a Reply

Your email address will not be published. Required fields are marked *

*

* Copy This Password *

* Type Or Paste Password Here *

HTML tags and attributes are not allowed.